Our Products

Exhaust Gas Heat Recovery Boiler

SOLUTIONS FOR COVID-19 , coronavirus

Testing done at DHS' advanced bio containment lab in Maryland, said the virus' half life plunges "drastically" with exposure to higher temperatures and even minimal exposure to humidity.
All boilers are designed and built in accordance with requirements of the ASME Boiler and Pressure Vessel Code

WNS Series Gas / Oil Hot Water Boiler

Capacity: 0.7 - 14 MW Pressure: 0.7 - 1.25 Mpa Learn More

SZS Series Gas / Oil Hot Water Boilers

Capacity: 7 - 116 MW Pressure: 1.0 - 1.6 Mpa Learn More

DZL Series Biomass Fired Steam Boilers

Capacity: 2 – 20 t/h Pressure: 1 - 2.5 Mpa Learn More

Exhaust heat recovery system - Wikiped

In transportation, an exhaust heat recovery system turns thermal losses in the exhaust pipe into energy. This technology seems to be more and more of interest by car and heavy-duty vehicle manufacturers as an efficient way to save fuel and reduce vehicles’ CO 2 emissions. [citation needed] This technology can be used either on a hybrid vehicle or a conventional one: it produces either

Waste Heat Recovery System - an overview | ScienceDire

Some important points and observations relating to gas turbine waste-heat recovery are: • Multipressure Steam Generators. These are becoming increasingly popular. With a single-pressure boiler, there is a limit to the heat recovery because the exhaust gas temperature cannot be reduced below the steam saturation temperature. This problem is

Exhaust Gas Boilers And Economisers working procedu

File Size: 2MB Exhaust Gas Boilers And Economisers working procedure The use of exhaust gases from diesel engine: The use of exhaust gases from diesel main propulsion engines to generate steam is a means of heat energy recovery and improved plant efficiency. An exhaust gas heat exchanger is shown in Figure above.

Techno-economic analysis on a new conceptual design

Recovering waste heat from boiler exhaust flue gas is an effective way to improve energy utilization efficiency and reduce coal burning pollution of coal-fired power plant (CFPP). The low-pressure economizer (LPE) is the most widely employed in waste heat recovery from boiler exhaust flue gas.

Alfa Laval - Exhaust gas waste heat recove

The recovery of waste heat is a unique opportunity that benefits operating economy as much as it does the environment. With as much as 35% of an engine’s fuel energy going into the exhaust flow as waste heat, there are substantial savings to be made when that energy is recovered.

Heat Recovery from Boiler Exhaust Gases | Physics Foru

Jan 05, 2015· For the purposes of all calculations assume that natural gas is 100% Methane (CH4). The pressure in the combustion chamber of the boiler and throughout the heat recovery system is 1 bar. The exhaust gases are blown down a plastic pipe situated in a room are then exhausted to atmosphere, as shown in the diagram attached.

Exhaust Heat Recove

Exhaust Heat Recovery Systems. Cain Industries has developed a complete line of heat exchangers for the three basic markets: Diesel and Gas Cogeneration, Boiler Exhaust Economizers and Fume Incineration. These systems have been designed solely for the recovery of waste exhaust heat from combustion sources.

Flue Gas Heat Recovery Systems - TheGreenA

File Size: 2MB Flue Gas Heat Recovery Systems (FGHRS) take advantage of heat within waste flue gases resulting from the combustion of gas in your boiler. This recovered heat is used to preheat the cold water entering the boiler, thereby lowering the amount of energy needed to warm the water up to the required level.

WASTE HEAT RECOVERY BOILERS - Johnston Boil

Cited by: 1 Waste Heat Inlet Gas Temperature °F 600—2,500 Waste Heat Mass Gas Flow Lbs/hr 1,000—400,000 FIG. 1 Since 1864 Johnston Boiler Company has built a reputation on innovative designs and rigid adherence to quality. We believe that boilers must be dependable. Today, as in 1864, Johnston’s employees take personal pride in the

Industrial Boilers Heat Recovery Steam Generators - Clayt

Call today to learn more about Clayton Exhaust Gas Boilers and industrial boilers heat recovery steam generators. Clayton Waste Heat Boilers Built from the coil sections of Clayton’s fired steam generators, these units are used for higher exhaust gas inlet temperatures up to 3,000°F, and are capable of handling exhaust gas flows in the

Boiler Economizer Exhaust Heat Recovery Syste

File Size: 2MB ASME designed at 750 PSIG this RTR is rated for a 150,000 lb/hr steam boiler. With an exhaust gas flow rate of more than 36,000 SCFM, it saves the end user over $450,000 each year in fuel costs. We engineer and manufacture combustion heat recovery systems …